Disassembling Neo1973/de
From Openmoko
NOTE: Die Zerlegen des Neo1973 Seite zeigt, wie man die GTA01Bv3 Hardware Revision öffnet. Zukünftige Hardware Revisions können Updates an dieser Anleitung benötigen . Jedoch benutzen das GTA01B4 (wird zur Zeit ausgeliefert) und das GTA02 (die Version die im Oktober veröffentlicht wird) das gleiche Gehäuse. |
Contents |
Rückseite des Neo1973
Öffnen der Rückabdeckung
Um die Rückabdeckung zu entfernen muss man mit dem Fingernagel vorsichtig in der kleinen Aussparung an der Oberseite des Neo's ziehen.
NOTE: Die beiden Torx Schrauben müssen entfernt werden. (T6x40) |
Vorsichtiges Entfernen der Frontabdeckung
Um die Frontabdeckung zu entfernen muss man vorsichtig mit dem Gitarren-Plektrum To remove the top cover, after removing the two Torx screws, carefully squeeze the end of the supplied guitar pick between the cover and the case at the bottom of the device, and then slide the pick up to the top on one side (do not twist the pick). As you slide the pick along, the case retaining clips should come apart with a snapping sound. Repeat the procedure for the other side of the device. To unclip the last remaining large retaining clip at the top, slide the pick all the way to the top (this can be difficult) and then press it in at the centre. By careful application of force the clip will detach and the cover can then be removed.
Frontabdeckung entfernt
Auf dem Bild sieht man von rechts beginnend im Uhrzeigersinn:
- Die eckige Baugruppe am rechten Rand ist die GPS-Antenne.
- Links davon befinden sich zwei goldene Anschlusspads für den Kopfhörer
- Der Debug Board Anschluss.
- Das Schwarze Bauteil auf der linken Seite ist die GSM-Antenne.
- Das schwarz/goldene Bauteil rechts daneben ist das Mikrofon.
- Am rechten oberen Ende befindet sich der Aux Knopf
- Rechts darunter befindet sich eine kleine Batterie. Diese sieht man auch auf dem nächsten Bild.
In der Mitte ist das berührungsempfindliche LC-Display (touchscreen) zu sehen. Die Anschluss-Leiterbahnen kann man an der linken unteren Ecke durch das Glas erkennen.
Anheben der Platine auf der linken Seite
NOTE: Man muss das Kunststoffgehäuse etwas nach außen biegen, damit der Kopfhöreranschluss freigelegt werden kann. |
Platine aus dem Gehäuse entnehmen
NOTE: Da die Platine nun auf einer Seite locker ist, kann man den USB-Anschluss und die GPS-Antenne vorsichtig aus der rechten Seite des Gehäuses ziehen und anschließend nach oben klappen. |
Auf dem Bild erkennt man:
- Bluetooth Modul mit der viereckigen Bluetooth-Antenne auf der kleinen grünen Platine am oberen Rand
- Die Kopfhörer-Buchse befindet sich rechts daneben.
- Darunter befindet sich der Neo1973 Batterie Anschluss.
- Die beiden goldenen, viereckigen Anschlusspads versorgen den Vibrationsmotor.
- Rechts neben der Kopfhörer-Buchse ist der Anschluss für den linken Lautsprecher.
On the other side of the PCB, going from bottom-right corner down-left.
- The small circular connector is the GSM connector to which an external aerial can be connected with the back removed, or with an alternative back.
- To the left of this is the right speaker connector.
- One of the button switches.
- USB port.
- Micro-SD slot
- SIM slot - overlaying the Micro-SD slot when present.
- Gold GPS antenna connector.
- Immediately above this with the grey wire connection is the connection to the built in GPS antenna.
On the case picture below, you can see the left and right speakers under the translucent plastic, and the vibrator motor in the middle.
Empty case frame
You can actually see the two stereo speakers beneath the translucent cover, and next to it the small vibrator motor.
Next to the top of the picture is a hole near the speaker. The external GSM antenna connector is accessed through this hole.
GSM Antenna
Languages: |
English • العربية • Български • Česky • Dansk • Deutsch • Esperanto • Eesti • Español • فارسی • Suomi • Français • עברית • Magyar • Italiano • 한국어 • Nederlands • Norsk (bokmål) • Polski • Português • Română • Русский • Svenska • Slovenčina • Українська • 中文(中国大陆) • 中文(台灣) • Euskara • Català |