Neo FreeRunner Wifi
From Openmoko
(→WEP) |
(udhcpc requires "-i" for specifying a custom network interface) |
||
(42 intermediate revisions by 20 users not shown) | |||
Line 1: | Line 1: | ||
− | {{Languages|Neo FreeRunner | + | {{Languages|Neo FreeRunner Wifi}} |
This page documents the [http://en.wikipedia.org/wiki/Wireless_networking wireless networking] solutions commonly known as [http://en.wikipedia.org/wiki/Wireless_LAN WLAN] or WiFi. | This page documents the [http://en.wikipedia.org/wiki/Wireless_networking wireless networking] solutions commonly known as [http://en.wikipedia.org/wiki/Wireless_LAN WLAN] or WiFi. | ||
There are other ways to enable wireless communications on the Neo, including [[Bluetooth]]. For Bluetooth solutions, see [[How to use bluetooth to transfer data between Neo and Desk-top]] and [[Manually using Bluetooth]]. | There are other ways to enable wireless communications on the Neo, including [[Bluetooth]]. For Bluetooth solutions, see [[How to use bluetooth to transfer data between Neo and Desk-top]] and [[Manually using Bluetooth]]. | ||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
== How can I tell what Access Points (APs) are visible to me? == | == How can I tell what Access Points (APs) are visible to me? == | ||
Line 67: | Line 57: | ||
=== Using wpa_supplicant manually === | === Using wpa_supplicant manually === | ||
− | Create and edit a suitable [[GTA02_WLAN#Sample_wpa_supplicant.conf|/etc/wpa_supplicant/wpa_supplicant.conf]]. | + | Create and edit a suitable [[GTA02_WLAN#Sample_wpa_supplicant.conf|/etc/wpa_supplicant/wpa_supplicant.conf (see below)]]. |
Bring up your wireless connection: | Bring up your wireless connection: | ||
− | root@om-gta02:~# | + | root@om-gta02:~# ifconfig eth0 up |
− | root@om-gta02:~# wpa_supplicant - | + | root@om-gta02:~# wpa_supplicant -i eth0 -c /etc/wpa_supplicant/wpa_supplicant.conf -B |
− | root@om-gta02:~# udhcpc eth0 | + | root@om-gta02:~# udhcpc -i eth0 |
=== Using WPA and /etc/network/interfaces === | === Using WPA and /etc/network/interfaces === | ||
− | Once you have a [[GTA02_WLAN#Sample_wpa_supplicant.conf|/etc/wpa_supplicant/wpa_supplicant.conf]] file, add a line under the eth0 entry in /etc/network/interfaces: | + | Once you have a [[GTA02_WLAN#Sample_wpa_supplicant.conf|/etc/wpa_supplicant/wpa_supplicant.conf (see below)]] file, add a line under the eth0 entry in /etc/network/interfaces: |
iface eth0 inet dhcp | iface eth0 inet dhcp | ||
Line 85: | Line 75: | ||
# ifdown eth0 && ifup eth0 | # ifdown eth0 && ifup eth0 | ||
− | You'll get a lot of messages, like <tt>ioctl[SIOCSIWENCODEEXT]: Operation not supported</tt> and <tt>sed: unrecognized option `--quiet'</tt>, they appear to be harmless. The "--quiet" error message can be avoided by replacing "sed --quiet" with "sed -n" in /etc/wpa_supplicant/*.sh | + | You'll get a lot of messages, like <tt>ioctl[SIOCSIWENCODEEXT]: Operation not supported</tt> and <tt>sed: unrecognized option `--quiet'</tt>, they appear to be harmless. The "--quiet" error message can be avoided by replacing "sed --quiet" with "sed -n" in /etc/wpa_supplicant/*.sh ([http://docs.openmoko.org/trac/ticket/2189 bug #2189]) |
=== wpa_supplicant.conf === | === wpa_supplicant.conf === | ||
+ | <tt>wpa-supplicant</tt>'s conf file typically found at <tt>/etc/wpa_supplicant/wpa_supplicant.conf</tt>. | ||
==== wpa_supplicant.conf explained ==== | ==== wpa_supplicant.conf explained ==== | ||
Line 117: | Line 108: | ||
==== Sample wpa_supplicant.conf ==== | ==== Sample wpa_supplicant.conf ==== | ||
+ | |||
+ | Sample <tt>/etc/wpa_supplicant/wpa_supplicant.conf</tt> : | ||
ctrl_interface=/var/run/wpa_supplicant | ctrl_interface=/var/run/wpa_supplicant | ||
Line 164: | Line 157: | ||
} | } | ||
− | ==== Other sample wpa_supplicant.conf files ==== | + | ==== Other working sample wpa_supplicant.conf files ==== |
Tom Yates documents his success [http://www.teaparty.net/technotes/openmoko-2.html#Wifi here] | Tom Yates documents his success [http://www.teaparty.net/technotes/openmoko-2.html#Wifi here] | ||
+ | |||
+ | Matthias Apitz documents his success here: [http://www.unixarea.de/openmoko.txt http://www.unixarea.de/openmoko.txt] (see chapter 6.). | ||
+ | |||
+ | ==== Roaming ==== | ||
+ | * Connecting to a local network with usb networking enabled, may get you into trouble. The default /etc/network/interfaces will configure the usb endpoint as a default gateway (for 2008.12). If you connect to another 192.168.0.0/24 network your phone will try the usb, timeout and then go for the other: remove the route with 'route del default gw 192.168.0.200'. Optionally remove the route from <tt>interfaces</tt> if you never intend to use your desktop as a router. | ||
+ | * You can have wpa_supplicant roam for you by setting the inet method to manual and using wpa_roam instead of wpa_conf in your /etc/network/interfaces. | ||
+ | * After bringing up the interface with wpa_supplicant, you can run wpa_cli and issue the command 'status' to see if and to which AP you are connected. | ||
+ | |||
+ | ==== Using with fsoraw ==== | ||
+ | wpa_supplicant can be invoked through fsoraw by running, | ||
+ | |||
+ | fsoraw -r WiFi -- wpa_supplicant -ieth0 -Dwext -c /etc/wpa_supplicant/wpa_supplicant.conf | ||
+ | |||
+ | * Remember there is no need to enable WiFi radio in Settings>Connectivity as fsoraw will enable it. | ||
+ | * The above command shall not return back to the shell, it can be sent to background using & | ||
+ | * To terminate the connection, kill wpa_supplicant | ||
== WEP == | == WEP == | ||
Line 187: | Line 196: | ||
If an incorrect key was set, please stop all activity on the interface for at least two minutes (i.e., killall udhcpc and ifconfig eth0 down), then issue the correct iwconfig command and retry. | If an incorrect key was set, please stop all activity on the interface for at least two minutes (i.e., killall udhcpc and ifconfig eth0 down), then issue the correct iwconfig command and retry. | ||
+ | |||
+ | ==== Manually setting WEP key with index different than 1 ==== | ||
+ | |||
+ | First you need to specify the key with its index as prefix or postfix: | ||
+ | |||
+ | # iwconfig eth0 key A4BEB3B8EC [2] | ||
+ | |||
+ | At this point, iwconfig doesn't show any key is used. Now you need to tell it to actually use key with index 2: | ||
+ | |||
+ | # iwconfig eth0 key [2] | ||
+ | |||
+ | Now your network with nonstandard wep index should work :) | ||
=== Using WEP and /etc/network/interfaces === | === Using WEP and /etc/network/interfaces === | ||
Line 200: | Line 221: | ||
Save your changes and run: | Save your changes and run: | ||
# ifdown eth0 && ifup eth0 | # ifdown eth0 && ifup eth0 | ||
+ | Idea : You can use [http://www.opkg.org/package_28.html ShortOm] to lauch this command on futur boot to activate wifi without having to use terminal | ||
== Known Issues == | == Known Issues == | ||
− | === | + | === iwconfig doesn't work in all cases === |
− | + | ||
− | + | ||
− | + | ||
− | + | ||
− | + | ||
+ | Note that for some reason our iwconfig requires a more constrained format than the generic iwconfig. See | ||
+ | [[Neo_FreeRunner_Wifi#Using_iwconfig_manually| using iwconfig manually]]. | ||
=== Anecdotal solutions === | === Anecdotal solutions === | ||
Line 218: | Line 237: | ||
Some APs apparently get upset by power managed devices, and the Freerunner enables power management of the wifi by default to preserve battery. One user's wrt54g certainly gets upset from time to time if he connect with the FreeRunner, sometimes refusing to talk to _anything_ over wifi afterwards until rebooted. | Some APs apparently get upset by power managed devices, and the Freerunner enables power management of the wifi by default to preserve battery. One user's wrt54g certainly gets upset from time to time if he connect with the FreeRunner, sometimes refusing to talk to _anything_ over wifi afterwards until rebooted. | ||
+ | |||
+ | <pre> | ||
+ | iwconfig eth0 power off | ||
+ | </pre> | ||
==== Modified script ==== | ==== Modified script ==== | ||
Line 236: | Line 259: | ||
"Could not get it to work properly on channel 11, so I set my accesspoint to channel 1." | "Could not get it to work properly on channel 11, so I set my accesspoint to channel 1." | ||
+ | |||
+ | ==== Make your WIFI more reliable ==== | ||
+ | After boot or before connecting do: | ||
+ | wmiconfig -i eth0 --power maxperf | ||
+ | of course you need to find [[wmiconfig]] or to compile it | ||
+ | |||
+ | ==== eth0 doesn't show up ==== | ||
+ | If a "config -a" or "lshw -c network" doesn't show the wlan interface (eth0) you might need to bind it first: | ||
+ | |||
+ | <pre> | ||
+ | echo s3c2440-sdi > /sys/bus/platform/drivers/s3c2440-sdi/bind | ||
+ | </pre> | ||
+ | |||
+ | If you are using FSO try using dbus. | ||
+ | |||
+ | <pre> | ||
+ | root@om-gta02:~$cat scripts/wifi-on.sh | ||
+ | #!/bin/sh | ||
+ | mdbus -s org.freesmartphone.odeviced /org/freesmartphone/Device/PowerControl/WiFi org.freesmartphone.Resource.Enable | ||
+ | |||
+ | </pre> | ||
== Wake up from wireless (wow)== | == Wake up from wireless (wow)== | ||
Line 257: | Line 301: | ||
1. wmiconfig --sethostmode asleep /* to tell ar6k what host's current is */ | 1. wmiconfig --sethostmode asleep /* to tell ar6k what host's current is */ | ||
2. wmiconfig --setwowmode enable /* enable wow function */ | 2. wmiconfig --setwowmode enable /* enable wow function */ | ||
− | 3. wmiconfig -- | + | 3. wmiconfig --addwowpattern 0 1 33 01 ff /* add packet filter pattern, this is the ICMP filter pattern */ |
4. apm -s | 4. apm -s | ||
5. ping IP_of_Neo | 5. ping IP_of_Neo | ||
Line 274: | Line 318: | ||
- To filter for ICMP packets (offset 33) | - To filter for ICMP packets (offset 33) | ||
wmiconfig --addwowpattern 0 1 33 01 ff | wmiconfig --addwowpattern 0 1 33 01 ff | ||
− | |||
− | |||
== A very ugly /etc/init.d/wlan startscript == | == A very ugly /etc/init.d/wlan startscript == | ||
Line 298: | Line 340: | ||
wpa_supplicant -ieth0 -c/etc/wpa_supplicant/wpa_supplicant.conf -B | wpa_supplicant -ieth0 -c/etc/wpa_supplicant/wpa_supplicant.conf -B | ||
sleep 10 | sleep 10 | ||
− | udhcpc eth0 | + | udhcpc -i eth0 |
RETVAL=$? | RETVAL=$? | ||
return $RETVAL | return $RETVAL | ||
Line 339: | Line 381: | ||
Wifi is faster than USB, so it is a good idea to tell the FreeRunner to connect through it. Put the following in /etc/network/interfaces under eth0: | Wifi is faster than USB, so it is a good idea to tell the FreeRunner to connect through it. Put the following in /etc/network/interfaces under eth0: | ||
− | up route del default gw 192.168.0.200 | + | up route del default gw 192.168.0.200 |
This will remove your computer as the default gateway and use the wireless one when the interface is brought up. User nickd reports that sometimes it fails so he has had to put it in twice. | This will remove your computer as the default gateway and use the wireless one when the interface is brought up. User nickd reports that sometimes it fails so he has had to put it in twice. | ||
− | == ssh into FR over | + | == ssh into FR over Other Network Interfaces == |
− | dropbear, the ssh server, is configured to listen on the USB interface only. Wireless interfaces like wlan or bluetooth are disabled for security reasons (empty root password). | + | dropbear, the ssh server, is configured to listen on the USB interface only. Wireless interfaces like wlan or bluetooth are disabled for security reasons (empty root password). Therefore: |
− | + | * Be careful with this config file since it can close the only door into your phone. | |
+ | |||
+ | * '''Set a root password!''' | ||
+ | |||
+ | ==== ssh into FR over WiFi Only ==== | ||
+ | |||
+ | Change the /etc/default/dropbear from: | ||
DROPBEAR_PORT=`ip addr list usb0 | awk 'BEGIN { FS="[ /]+" } /inet / { print $3 }'`:22 | DROPBEAR_PORT=`ip addr list usb0 | awk 'BEGIN { FS="[ /]+" } /inet / { print $3 }'`:22 | ||
Line 354: | Line 402: | ||
into: | into: | ||
− | DROPBEAR_PORT=22 | + | DROPBEAR_PORT=`ip addr list eth0 | awk 'BEGIN { FS="[ /]+" } /inet / { print $3 }'`:22 |
− | + | (which now prepends the eth0 (WLAN interface) ip address before the :22) | |
− | + | ==== ssh into FR over Any Network Interface ==== | |
+ | |||
+ | Change the /etc/default/dropbear from: | ||
+ | |||
+ | DROPBEAR_PORT=`ip addr list usb0 | awk 'BEGIN { FS="[ /]+" } /inet / { print $3 }'`:22 | ||
+ | |||
+ | (which actually only prepends the usb0 ip address before the :22) | ||
+ | |||
+ | into: | ||
− | = | + | DROPBEAR_PORT=*:22 |
− | + | == See also == | |
− | * [[Lint-wifi]] | + | * [[KnjMokoWifi]] GUI interface to administer WiFi connections |
− | * [[Mofi]] | + | * [[wmiconfig]] Atheros utility to config the wifi chip used in Neo FreeRunner |
− | * [[Camp-Wifi]] | + | * [[Lint-wifi]] GUI interface to administer WiFi connections |
+ | * [[Mofi]] GUI interface to administer WiFi connections | ||
+ | * [[Camp-Wifi]] GUI interface to administer WiFi connections | ||
== External links == | == External links == | ||
Line 373: | Line 431: | ||
[[Category:Neo FreeRunner Hardware]] | [[Category:Neo FreeRunner Hardware]] | ||
− | [[Category: | + | [[Category:Wlan software| ]] |
Latest revision as of 11:38, 10 March 2011
![]() |
Languages: |
English • العربية • Български • Česky • Dansk • Deutsch • Esperanto • Eesti • Español • فارسی • Suomi • Français • עברית • Magyar • Italiano • 한국어 • Nederlands • Norsk (bokmål) • Polski • Português • Română • Русский • Svenska • Slovenčina • Українська • 中文(中国大陆) • 中文(台灣) • Euskara • Català |
This page documents the wireless networking solutions commonly known as WLAN or WiFi.
There are other ways to enable wireless communications on the Neo, including Bluetooth. For Bluetooth solutions, see How to use bluetooth to transfer data between Neo and Desk-top and Manually using Bluetooth.
Contents |
[edit] How can I tell what Access Points (APs) are visible to me?
You can connect to wireless networks through wireless access points. If you want to know the names of all the access points that are currently visible to you, you can perform a scan with this command:
root@om-gta02:~# iwlist eth0 scan
If anything is visible you will get a list that looks something like this:
eth0 Scan completed : Cell 01 - Address: 00:16:B6:DE:77:58 ESSID:"StarvinMarvin" Mode:Master Frequency:2.437 GHz (Channel 6) Quality=9/94 Signal level=-86 dBm Noise level=-95 dBm Encryption key:on Extra:bcn_int=100 Extra:wpa_ie=dd180050f20101000050f20201000050f20201000050f2020000 Cell 02 - Address: 00:21:29:AA:10:97 ESSID:"CandT Network" Mode:Master Frequency:2.437 GHz (Channel 6) Quality=39/94 Signal level=-56 dBm Noise level=-95 dBm Encryption key:on Extra:bcn_int=100 Extra:wpa_ie=dd1c0050f20101000050f20202000050f2040050f20201000050f2020000 Extra:rsn_ie=30180100000fac020200000fac04000fac020100000fac020000 Cell 03 - Address: 00:14:95:1B:8E:B9 ESSID:"2WIRE852" Mode:Master Frequency:2.437 GHz (Channel 6) Quality=5/94 Signal level=-90 dBm Noise level=-95 dBm Encryption key:on Extra:bcn_int=100 Cell 04 - Address: 00:E0:98:52:3D:78 ESSID:"smith" Mode:Master Frequency:2.437 GHz (Channel 6) Quality=36/94 Signal level=-59 dBm Noise level=-95 dBm Encryption key:on Extra:bcn_int=100
If you want to connect to an unsecured network run:
udhcpc
[edit] WPA
WPA is an encryption method for securing your wireless network.
[edit] Using wpa_supplicant manually
Create and edit a suitable /etc/wpa_supplicant/wpa_supplicant.conf (see below).
Bring up your wireless connection:
root@om-gta02:~# ifconfig eth0 up root@om-gta02:~# wpa_supplicant -i eth0 -c /etc/wpa_supplicant/wpa_supplicant.conf -B root@om-gta02:~# udhcpc -i eth0
[edit] Using WPA and /etc/network/interfaces
Once you have a /etc/wpa_supplicant/wpa_supplicant.conf (see below) file, add a line under the eth0 entry in /etc/network/interfaces:
iface eth0 inet dhcp wpa-conf /etc/wpa_supplicant/wpa_supplicant.conf
Save your changes and run:
# ifdown eth0 && ifup eth0
You'll get a lot of messages, like ioctl[SIOCSIWENCODEEXT]: Operation not supported and sed: unrecognized option `--quiet', they appear to be harmless. The "--quiet" error message can be avoided by replacing "sed --quiet" with "sed -n" in /etc/wpa_supplicant/*.sh (bug #2189)
[edit] wpa_supplicant.conf
wpa-supplicant's conf file typically found at /etc/wpa_supplicant/wpa_supplicant.conf.
[edit] wpa_supplicant.conf explained
The highest priority is tried first then falls back to the next highest number.
priority=100 1st
then
priority=99
# Simple case: WPA-PSK, PSK as an ASCII passphrase, allow all valid ciphers network={ ssid="AP_ESSID" psk="presharedkey" priority=5 } #try open AP regardless of its SSID. # change root password before you go roaming around it could prove dangerous network={ key_mgmt=NONE priority=1 #try any open AP last }
A more in depth explanation can be found here:
http://hostap.epitest.fi/gitweb/gitweb.cgi?p=hostap.git;a=blob_plain;f=wpa_supplicant/wpa_supplicant.conf
[edit] Sample wpa_supplicant.conf
Sample /etc/wpa_supplicant/wpa_supplicant.conf :
ctrl_interface=/var/run/wpa_supplicant ctrl_interface_group=0 eapol_version=1 ap_scan=1 fast_reauth=1 # WPA2: network={ ssid="your ssid" scan_ssid=1 proto=RSN key_mgmt=WPA-PSK pairwise=CCMP TKIP group=TKIP CCMP psk="secret key" priority=50 } # WPA: network={ ssid="your_ssid" proto=WPA key_mgmt=WPA-PSK pairwise=TKIP group=TKIP scan_ssid=1 psk="secret key" priority=10 } # WEP: network={ ssid="your_ssid" scan_ssid=1 key_mgmt=NONE wep_tx_keyidx=0 wep_key0=your_hex_key priority=8 } # Open: network={ ssid="your ssid" key_mgmt=NONE priority=5 }
[edit] Other working sample wpa_supplicant.conf files
Tom Yates documents his success here
Matthias Apitz documents his success here: http://www.unixarea.de/openmoko.txt (see chapter 6.).
[edit] Roaming
- Connecting to a local network with usb networking enabled, may get you into trouble. The default /etc/network/interfaces will configure the usb endpoint as a default gateway (for 2008.12). If you connect to another 192.168.0.0/24 network your phone will try the usb, timeout and then go for the other: remove the route with 'route del default gw 192.168.0.200'. Optionally remove the route from interfaces if you never intend to use your desktop as a router.
- You can have wpa_supplicant roam for you by setting the inet method to manual and using wpa_roam instead of wpa_conf in your /etc/network/interfaces.
- After bringing up the interface with wpa_supplicant, you can run wpa_cli and issue the command 'status' to see if and to which AP you are connected.
[edit] Using with fsoraw
wpa_supplicant can be invoked through fsoraw by running,
fsoraw -r WiFi -- wpa_supplicant -ieth0 -Dwext -c /etc/wpa_supplicant/wpa_supplicant.conf
- Remember there is no need to enable WiFi radio in Settings>Connectivity as fsoraw will enable it.
- The above command shall not return back to the shell, it can be sent to background using &
- To terminate the connection, kill wpa_supplicant
[edit] WEP
WEP is an encryption method for securing your wireless network. WEP is generally considered to be weak, you should use WPA instead if possible.
[edit] Using iwconfig manually
Note that for WEP our iwconfig requires a more specific format than generic iwconfig.
The canonical way of running iwconfig for WEP would be something like this:
- iwconfig eth0 key A4BEB3B8EC essid xyz
Two things are important here:
- the key must be in HEX. iwconfig will not do anything useful if the key is given as a string. Here is a handy ASCII string to HEX converter.
- the ESSID must follow the key.
If an incorrect key was set, please stop all activity on the interface for at least two minutes (i.e., killall udhcpc and ifconfig eth0 down), then issue the correct iwconfig command and retry.
[edit] Manually setting WEP key with index different than 1
First you need to specify the key with its index as prefix or postfix:
- iwconfig eth0 key A4BEB3B8EC [2]
At this point, iwconfig doesn't show any key is used. Now you need to tell it to actually use key with index 2:
- iwconfig eth0 key [2]
Now your network with nonstandard wep index should work :)
[edit] Using WEP and /etc/network/interfaces
iface eth0 inet dhcp wireless-key my_wep_key wireless-essid my_essid
iface eth0 inet dhcp wpa-wep-key0 my_wep_key wpa-key-mgmt NONE wpa-ssid my_essid
Save your changes and run:
# ifdown eth0 && ifup eth0
Idea : You can use ShortOm to lauch this command on futur boot to activate wifi without having to use terminal
[edit] Known Issues
[edit] iwconfig doesn't work in all cases
Note that for some reason our iwconfig requires a more constrained format than the generic iwconfig. See using iwconfig manually.
[edit] Anecdotal solutions
These solutions worked for some people:
[edit] Disable power management
Some APs apparently get upset by power managed devices, and the Freerunner enables power management of the wifi by default to preserve battery. One user's wrt54g certainly gets upset from time to time if he connect with the FreeRunner, sometimes refusing to talk to _anything_ over wifi afterwards until rebooted.
iwconfig eth0 power off
[edit] Modified script
"I changed the script a little:
Exec=xterm -e "ifconfig eth0 down \ iwconfig eth0 txpower off channel 0 \ while killall wpa_supplicant; do echo 'Killing wpa_sup'; done \ killall udhcpc \ wpa_supplicant -i eth0 -c /etc/wpa_supplicant/wpa_supplicant.conf -D wext -B \ sleep 10; udhcpc"
Now it is working every time. I am using 2008.latest (081004) and a linksys WAP54G accesspoint,
[edit] Use a different channel
"Could not get it to work properly on channel 11, so I set my accesspoint to channel 1."
[edit] Make your WIFI more reliable
After boot or before connecting do:
wmiconfig -i eth0 --power maxperf
of course you need to find wmiconfig or to compile it
[edit] eth0 doesn't show up
If a "config -a" or "lshw -c network" doesn't show the wlan interface (eth0) you might need to bind it first:
echo s3c2440-sdi > /sys/bus/platform/drivers/s3c2440-sdi/bind
If you are using FSO try using dbus.
root@om-gta02:~$cat scripts/wifi-on.sh #!/bin/sh mdbus -s org.freesmartphone.odeviced /org/freesmartphone/Device/PowerControl/WiFi org.freesmartphone.Resource.Enable
[edit] Wake up from wireless (wow)
Wi-Fi module constantly drain currents after module power up, for wi-fi SIP phone or some application need long standby time, will need wake up from wireless function for power saving. There is a sleep mode that Ar6k supported for wake up from wireless.
http://svn.openmoko.org/trunk/src/target/AR6kSDK.build_sw.18/host/tools/wmiconfig
export ATH_CROSS_COMPILE_TYPE=arm-angstrom-linux-gnueabi- make
Debian package:
wget http://meshy.org/~ato/debian/pool/main/w/wmiconfig/wmiconfig_0.0.18-1_armel.deb dpkg -i wmiconfig_0.0.18-1_armel.deb
Basically, it's achieved via wmiconfig tool to issue IOCTL if we want ar6k wifi module to generate interrupt to host controller. The procedure to enable wakeup-on-wireless(wow) is listed here:
1. wmiconfig --sethostmode asleep /* to tell ar6k what host's current is */ 2. wmiconfig --setwowmode enable /* enable wow function */ 3. wmiconfig --addwowpattern 0 1 33 01 ff /* add packet filter pattern, this is the ICMP filter pattern */ 4. apm -s 5. ping IP_of_Neo 6. The GPIO1 pin would be pulled up. The system would resume then. 7. wmiconfig --sethostmode awake /* The firmware of ar6k will pull low the GPIO1 pin */
--addwowpattern <list-id> <pattern-size> <pattern-offset> <pattern> <pattern-mask>
Here are some addwowpattern commands:
Protocol type=IP=0800 Protocol type in IP header=ICMP=01
- To filter for IP packets(offset 22) wmiconfig --addwowpattern 0 2 22 0800 ffff - To filter for ICMP packets (offset 33) wmiconfig --addwowpattern 0 1 33 01 ff
[edit] A very ugly /etc/init.d/wlan startscript
#!/bin/sh # # wlan This shell script starts and stops wlan. # # processname: wlan # Source function library. #. /etc/rc.d/init.d/functions # "written" by HdR RETVAL=0 prog="wlan" # test -f /etc/default/$prog && . /etc/default/$prog start() { echo -n "Starting $prog: " ifconfig eth0 up wpa_supplicant -ieth0 -c/etc/wpa_supplicant/wpa_supplicant.conf -B sleep 10 udhcpc -i eth0 RETVAL=$? return $RETVAL } stop() { # Stop daemons. echo -n "Shutting down $prog: " killall wpa_supplicant ifconfig eth0 down # killproc gpsd RETVAL=$? return $RETVAL } # See how we were called. case "$1" in start) start ;; stop) stop ;; restart|reload) stop start RETVAL=$? ;; *) echo "Usage: $0 {start|stop|restart}" exit 1 esac exit $RETVAL
Note: Don't forget to make this script executable with "chmod +x <filename>"
[edit] Route internet connection through Wifi rather than USB
Wifi is faster than USB, so it is a good idea to tell the FreeRunner to connect through it. Put the following in /etc/network/interfaces under eth0:
up route del default gw 192.168.0.200
This will remove your computer as the default gateway and use the wireless one when the interface is brought up. User nickd reports that sometimes it fails so he has had to put it in twice.
[edit] ssh into FR over Other Network Interfaces
dropbear, the ssh server, is configured to listen on the USB interface only. Wireless interfaces like wlan or bluetooth are disabled for security reasons (empty root password). Therefore:
- Be careful with this config file since it can close the only door into your phone.
- Set a root password!
[edit] ssh into FR over WiFi Only
Change the /etc/default/dropbear from:
DROPBEAR_PORT=`ip addr list usb0 | awk 'BEGIN { FS="[ /]+" } /inet / { print $3 }'`:22
(which actually only prepends the usb0 ip address before the :22)
into:
DROPBEAR_PORT=`ip addr list eth0 | awk 'BEGIN { FS="[ /]+" } /inet / { print $3 }'`:22
(which now prepends the eth0 (WLAN interface) ip address before the :22)
[edit] ssh into FR over Any Network Interface
Change the /etc/default/dropbear from:
DROPBEAR_PORT=`ip addr list usb0 | awk 'BEGIN { FS="[ /]+" } /inet / { print $3 }'`:22
(which actually only prepends the usb0 ip address before the :22)
into:
DROPBEAR_PORT=*:22
[edit] See also
- KnjMokoWifi GUI interface to administer WiFi connections
- wmiconfig Atheros utility to config the wifi chip used in Neo FreeRunner
- Lint-wifi GUI interface to administer WiFi connections
- Mofi GUI interface to administer WiFi connections
- Camp-Wifi GUI interface to administer WiFi connections