USB Networking/zh tw
From Openmoko
Contents |
Neo1973 side
Name resolution
By default Neo1973 has usb0 interface working due to Ethernet gadget (g_ether) compiled into kernel.
On the Neo, if you want to reach out to the internets using full qualified hostnames, you need to define your DNS server. Create a file /etc/resolv.conf with at least one line saying
nameserver xxx.xxx.xxx.xxx
e.g. nameserver 192.168.1.1
Then you can also easily update your 2007.2 OpenMoko packages with "ipkg update && ipkg upgrade" on the Neo.
A better approach is it edit: /etc/network/interfaces and modify the line:
up echo nameserver 192.168.0.200 >/etc/resolv.conf
to specify your preferred DNS server instead of 192.168.0.200.
example: up echo nameserver 4.2.2.2 >/etc/resolv.conf
Another approach is to symlink (NOW OBSOLETE?)
ln -s /var/run/resolv.conf /etc/resolv.conf
and fill the file at bootup with a script /etc/network/if-up.d/08setupdns containing:
#!/bin/sh -e echo nameserver 192.168.0.200 > /var/run/resolv.conf
this way the file is correctly handled from ppp package when dialing into gprs.
Routing
You need a additional route for traffic to the internet. This traffic can be routed through your pc (see below) if the pc is the default route destination. you can achieve this by adding
gateway 192.168.0.200
to your /etc/network/interfaces in the usb0 section.
Desktop side
Manual method
With the device connected, modprobe usbnet module and configure usb0 interface (as root):
ifconfig usb0 192.168.0.200 netmask 255.255.255.0
If your eth0 interface is also in the same 'range' (e.g. 192.168.0.105) then you can do the following:
1. ping the Neo with
# ping -I usb0 192.168.0.202
2. add a route to your Neo:
# /sbin/route add -host 192.168.0.202/32 dev usb0
3 log in to the Neo
# ssh root@192.168.0.202
If you don't have the necessary modules to get usb0 going, make sure you have the following kernel options enabled:
- CONFIG_USB_USBNET
- CONFIG_USB_NET_CDCETHER
Both options are available in the Device Drivers -> USB support -> USB Network Adapters. For more info see the usbnet driver homepage.
Automatic method
Took from Hotplugging usbnet post by Marcin 'Hrw' Juszkiewicz.
Debian or similar
Edit /etc/network/interfaces:
allow-hotplug usb0 iface usb0 inet static address 192.168.0.200 netmask 255.255.255.0 network 192.168.0.0 post-up iptables -A POSTROUTING -t nat -j MASQUERADE -s 192.168.0.0/24 post-up echo 1 > /proc/sys/net/ipv4/ip_forward post-up iptables -P FORWARD ACCEPT
Ubuntu (Tested with Feisty, Gutsy and Hardy)
Edit /etc/network/interfaces:
auto usb0 iface usb0 inet static address 192.168.0.200 netmask 255.255.255.0 network 192.168.0.0 up iptables -A POSTROUTING -t nat -j MASQUERADE -s 192.168.0.0/24 & up echo 1 > /proc/sys/net/ipv4/ip_forward & up iptables -P FORWARD ACCEPT & down iptables -D POSTROUTING -t nat -j MASQUERADE -s 192.168.0.0/24 &
If you are doing the echo 1 > /proc/... command manually, sudo may not be enough, then you will have to execute it from a sudo bash.
Ubuntu Feisty, Gutsy and Hardy appear to have a bug where ifdown is not run when the interface is unplugged, meaning this only works once after the system is booted.
This was reported to ubuntu a long time ago, so don't file a duplicate bug. Write a comment instead at https://bugs.launchpad.net/ubuntu/+source/ifupdown/+bug/130437
One can patch /etc/udev/rules.d/85-ifupdown.rules, editing the two lines at the end of the file:
SUBSYSTEM=="net", DRIVERS=="?*", GOTO="net_start" GOTO="net_end" LABEL="net_start" # Bring devices up and down only if they're marked auto. # Use start-stop-daemon so we don't wait on dhcp ACTION=="add", RUN+="/sbin/start-stop-daemon --start --background --pidfile /var/run/network/bogus --startas /sbin/ifup -- --allow auto $env{INTERFACE}" LABEL="net_end" ACTION=="remove", RUN+="/sbin/start-stop-daemon --start --background --pidfile /var/run/network/bogus --startas /sbin/ifdown -- --allow auto $env{INTERFACE}"
the bug is that the LABEL="net_end" is at the wrong position
SuSE
/etc/sysconfig/network/ifcfg-usb0
# USB configuration for PDAs (openmoko) IPADDR=192.168.0.200 NETMASK=255.255.255.0 STARTMODE=onboot
Fedora (Tested with FC8)
/etc/sysconfig/network-scripts/ifcfg-usb0
# USB configuration for PDAs (openmoko) # from http://www.handhelds.org/moin/moin.cgi/UsbNet DEVICE=usb0 BOOTPROTO=none IPADDR=192.168.0.200 NETMASK=255.255.255.0 ONBOOT=yes
Red Hat or similar (tested with Workstation 5)
Edit /etc/sysconfig/network-scripts/net.hotplug:
After this command
case $INTERFACE in # interfaces that are registered after being "up" (?)
add
usb0) ifconfig usb0 192.168.0.200 netmask 255.255.255.0 route add 192.168.0.202 usb0 iptables -I INPUT 1 -s 192.168.0.202 -j ACCEPT iptables -I OUTPUT 1 -s 192.168.0.200 -j ACCEPT iptables -A POSTROUTING -t nat -j MASQUERADE -s 192.168.0.0/24 echo 1 > /proc/sys/net/ipv4/ip_forward exit 0 ;;
Gentoo
- Open /etc/conf.d/net and add:
# Neo1973 config_usb0=( "192.168.0.200 netmask 255.255.255.0" ) routes_usb0=( "192.168.0.202/32 via 192.168.0.200" )
- Create a new init script:
cd /etc/init.d ln -s net.lo net.usb0
- Put iptables into use:
iptables -I INPUT 1 -s 192.168.0.202 -j ACCEPT iptables -I OUTPUT 1 -s 192.168.0.200 -j ACCEPT iptables -A POSTROUTING -t nat -j MASQUERADE -s 192.168.0.0/24
- Store them
/etc/init.d/iptables save
- If you want the routing by default:
rc-update add iptables default
- You must also inform the kernel, to start forwarding. One way to automate this is to create /etc/conf.d/net.usb0 as follows
preup() { echo 1 > /proc/sys/net/ipv4/ip_forward return 0 } postdown() { echo 0 > /proc/sys/net/ipv4/ip_forward return 0 }
This way, packet forwarding will be turned on when Neo is plugged in, and off when it's not.
MacOS X
See the USB Networking section in the MacOS X article.
Mobile development
Proxying DNS requests
If, like me, you move about quite a lot, connecting to various networks as you go and getting your ip via dhcp, you'll probably be annoyed at having to constantly update your resolv.conf on the Neo 1973.
To get round this, as part of my setup script, I run a proxy dns on the ip address the neo comes in on at the usb0 port. This means that my Neo /etc/resolv.conf only contains:
nameserver 192.168.0.200
and my laptop will proxy all dns requests based on it's own /etc/resolv.conf
note that we only run the dns proxy on the usb0 interface so that we don't break any other networking
Proxying with dnrd
The script is designed to use dnrd as the dns proxy. The script and a copy of dnrd are available from my site. The script also performs the initial setup of the connection as per the USB_Networking#Manual_method above.
Proxying with a UDP forwarder
Another easy setup is using a udp forwarder like the one from http://www.tapor.com/udpf/ - is use it with the command
udpf-elf\ -p=53\ -f=`cat /etc/resolv.conf|awk '$1 == "nameserver"{print $2; exit(0);}'`:53
Proxying with iptables
Its is possible to forward DNS requests with iptables using the DNAT target
iptables -t nat -A PREROUTING -p tcp -s 192.168.0.202 -d 192.168.0.200 --dport domain -j DNAT --to-destination 192.168.0.1 iptables -t nat -A PREROUTING -p udp -s 192.168.0.202 -d 192.168.0.200 --dport domain -j DNAT --to-destination 192.168.0.1
where 192.168.0.1 is the IP of your residential gateway (router). This is the easiest method, but its not recommended if you have a direct connection to the Internet as ISP DNS servers can change, and this does no load-balancing.
Connecting to phone
Then ssh root@192.168.0.202 with empty password to get into phone.
NOTE: the ssh daemon (dropbear 0.49) on the OpenMoko appears to have a bug when sending the exit status back to the client. From time to time you receive an exit status of 255.
SSH Extras
If you get fed up with typing root@192.168.0.202, on your PC edit /etc/hosts and add an entry for 'phone'
192.168.0.202 phone
then edit ~/.ssh/config (or create it) and add
host phone user root
then all you need to do is type
# ssh phone
To avoid ssh added a new line for every ssh host-key to you known_hosts you can add the following to the phone section in ~/.ssh/config
UserKnownHostsFile /dev/null
You might want to use keys to bypass the login prompt too.
SSH Keys
From host to phone
To generate ssh keys for use as a login mechanism type
ssh-keygen -t rsa
when prompted for a password either hit enter for no password (not really a good idea) or enter a password for this key. ssh into the phone and create ~/.ssh
# mkdir ~/.ssh
then from your PC copy the .pub file to the phone.
# scp ~/.ssh/id_rsa.pub phone:.ssh/authorized_keys
You should now be able to ssh directly into the phone.
To disable password logins (after setting up key access) edit /etc/init.d/dropbear and change the following line:
DROPBEAR_EXTRA_ARGS=
to
DROPBEAR_EXTRA_ARGS="-s"
You will need to restart dropbear for this to take effect.
From phone to host
Generate the key
dropbearkey -t rsa -f id_rsa
The output will look something like this:
Will output 1024 bit rsa secret key to 'id_rsa' Generating key, this may take a while... Public key portion is: ssh-rsa AAAAB3Nza[...] Fingerprint: md5 ca:e8:f0:b7:f6:7b:c2:b6:b9:71:e4:45:86:a9:ff:b8
Copy and paste the one line (in this example, starting with 'ssh-rsa' onto the end of the host's authorized_keys file (often in ~/.ssh/).
From the phone, ssh with -i:
ssh -i id_rsa user@host
This works for me. I ripped off these instructions from: [[1]]
GUI on desktop through SSH
If you need to get the GUI on the phone onto the desktop via usb, you can use ssh as follows
ssh -l root -X -v 192.168.0.202
Login, and run openmoko-finger-demo for example, and it will open up on the desktop. To get landscape view, just resize the GUI window on the desktop.
Remote apps on neo
To get desktop apps to show up on your neo, first log in to the phone
ssh -l root 192.168.0.202
Then once inside, run:
DISPLAY=:0 xhost +192.168.0.200
After this you can close the ssh session. Back on the desktop computer, run:
DISPLAY=moko:0 xclock
Note that the xhost command will allow remote applications on 192.168.0.200 to access the X server. It will allow anyone on the desktop machine to access the X server of the neo, including snooping anything you type on it. To disallow remote applications again, run this in the neo:
DISPLAY=:0 xhost -192.168.0.200
![]() |
Languages: |
English • العربية • Български • Česky • Dansk • Deutsch • Esperanto • Eesti • Español • فارسی • Suomi • Français • עברית • Magyar • Italiano • 한국어 • Nederlands • Norsk (bokmål) • Polski • Português • Română • Русский • Svenska • Slovenčina • Українська • 中文(中国大陆) • 中文(台灣) • Euskara • Català |