Moving current system from flash to SD
From Openmoko
m (Category: -Technical, +Flashing Openmoko) |
m (typo) |
||
(One intermediate revision by one user not shown) | |||
Line 3: | Line 3: | ||
Typical scenario : | Typical scenario : | ||
* running 2007.2 from flash | * running 2007.2 from flash | ||
− | * want to install OM 2008.8 without loosing the "backup" 2007.7 in | + | * want to install OM 2008.8 without loosing the "backup" 2007.7 in case of need, to be booted from SD |
Necessary steps (to be confirmed, don't try this unless you know what you're doing !) : | Necessary steps (to be confirmed, don't try this unless you know what you're doing !) : | ||
Line 45: | Line 45: | ||
You should verify it's a "u-boot/PPCBoot image" with the command "file" | You should verify it's a "u-boot/PPCBoot image" with the command "file" | ||
+ | |||
[[category:Flashing Openmoko]] | [[category:Flashing Openmoko]] | ||
+ | [[Category:MicroSD]] |
Latest revision as of 07:34, 13 January 2010
This is an attempt at describing how one can "backup" or move an existing current system running in the FR flash NAND to the micro SD card, in order to boot from it. See associate thread here.
Typical scenario :
- running 2007.2 from flash
- want to install OM 2008.8 without loosing the "backup" 2007.7 in case of need, to be booted from SD
Necessary steps (to be confirmed, don't try this unless you know what you're doing !) :
- Establish a running system on SD (see Booting from SD)
- reboot from that alternate system on SD
- from that system on SD, transfer content of flash to a backup dir on SD (provided SD is big enough to hold 2 systems)
- flash with new system
- reboot under newly flashed system
- remove old system from SD's root (the one which was booted in before to do the backup)
- move the backup from the backup dir of the SD to the root of the SD
- change what's necessary in the backup (/etc/fstab ?) so that it will work when booted on SD
- similarly adjust kernels available on SD
- test the dual-booting from flash or SD
More details about each steps needed.
[edit] Backup of system in flash to a backup dir on SD
Assuming one has booted from a system on SD already, this would create a copy of the root partition in the freerunner's flash to a "/backup-dir" directory, on the SD.
# mkdir /mnt/memroot/ # mkdir /backup-dir # mount -t jffs2 -o ro /dev/mtdblock6 /mnt/memroot/ # this for a freerunner # cd /mnt/memroot; rsync -avx --progress . /backup-dir/
You can leave away the --progress rsync option if you don't want to see a progress report (xfer#x, to-check y/z) while copying. See Partitions for details of the partitions in flash (hence the /dev/mtdblock6).
Instead of using rsync you could also use one of the following ways to perform copying (please correct if not working)
# cd /mnt/memroot; find . -depth | cpio -pdmv /backup-dir/ # cd /mnt/memroot; tar cpf - . | tar xvpf - -C /backup-dir/
The following may also work, but is not recommended, as there are problems copying certain files with cp -a: then be sure to check that your backup and original are identical!
# cp -a /mnt/memroot/. /backup-dir/.
[edit] Verify that backup directory is identical to source partition
To verify that you copied everything, you can use rsync (again), but now additionally with the -n option
# cd /mnt/memroot; rsync -avxn . /backup-dir/
[edit] Transfer kernel to FAT partition
See inside /boot, where you should find a "/boot/uImage-2.6.24" image, ready to be put on the FAT partition to be used by u-boot.
You should verify it's a "u-boot/PPCBoot image" with the command "file"