View source for Neo1973 OpenOCD/zh cn
From Openmoko
You do not have permission to edit this page, for the following reasons:
You can view and copy the source of this page:
Template used on this page:
Return to Neo1973 OpenOCD/zh cn.
You do not have permission to edit this page, for the following reasons:
You can view and copy the source of this page:
Template used on this page:
Return to Neo1973 OpenOCD/zh cn.
OpenOCD 是完全免费的片上调式软件(On-chip-debugger),类似Debug Board。
它为目标程序的挂起和恢复,寄存器,内存的读写等提供一个易读的telnet接口,
同时,还在tcp端口提供一个远程gdb调试接口。
最初在Debug Board设计出来之前,GTA01开发组就是使用OpenOCD结合wiggler作为他们的调试工具的。
通过MokoMakefile 构建openmoko开发工具"make openmoko-devel-tools" 将会生成openocd和dfu-util的二进制文件。构建时需要使用 "bitbake openocd-native" 命令。
我们现在可以从http://people.openmoko.org/laforge/dpkg 获得debian包。安装openocd,执行
dpkg --install openocd_82-1_i386.deb
您还可以在Debian/Unstable找到OpenOCD的deb包。
There is an experimental ebuild for openocd in the gentoo bugzilla.
OpenOCD 82以后的版本已经可以很好的工作在 QT2410 和 Neo1973 目标板上了。您可以通过svn获得代码,例如获得版本130的源代码:
svn co -r 130 http://svn.berlios.de/svnroot/repos/openocd/trunk
The YAGARTO Project provides a Win32 installer for OpenOCD. Details and download can be found at http://www.yagarto.de/howto/openocd/index.html. This will then work with the FDTI drivers available from http://people.openmoko.org/laforge/misc/debug_board_v2/windows_drivers/
User:HaraldWelte has provided a openocd.cfg configuration file for use of OpenOCD with wiggler and the QT2410 target board.
We cannot provide a full manual for OpenOCD, but please check Bootloader#Using_JTAG_to_boot_from_RAM and NAND bad blocks#JTAG_.2F_OpenOCD_.2F_u-boot_RAM_based, as well as the Neo1973 OpenOCD#Using OpenOCD telnet interface section below.
This has been reported upstream. Bugfix pending.
An easily made but devastating mistake is to forget to actually activate the CPU. Just connecting power is not enough ! Press and hold the power button until the boot loader does its count-down, or, in case there is no runnable boot loader, the CPU keeps itself busy.
You get something like:
Error: jtag.c:1224 jtag_examine_chain(): number of discovered devices in JTAG chain (51) doesn't match configuration (1)
This seems like a libftdi initialization bug. Sometimes the FT2232 doesn't get completely reset into a sane state at startup of OpenOCD. Please unplug the USB cable from the Amontec JTAGkey / Debug Board and re-plug. It should immediately work the next time. Bugfix would be appreciated a lot!
Another common error is this one:
JTAG communication failure, check connection, JTAG interface, target power etc.
Also this one is fixed by unplugging and re-plugging USB.
If you want to use OpenOCD with our Debug Board v2, and want to use the serial port simultaneously with OpenOCD, you need libftdi-0.8 or later. Chances are high that your distribution still ships an earlier version of libftdi, so you might want to download it from http://www.intra2net.com/de/produkte/opensource/ftdi/ and build yourself.
This is an openocd.cfg that is known to work with Debug Board (v2/v3), Neo1973 Hardware#GTA01Bv3 and OpenOCD 130:
telnet_port 4444 gdb_port 3333 interface ft2232 jtag_speed 0 ft2232_vid_pid 0x1457 0x5118 ft2232_layout "jtagkey" reset_config trst_and_srst jtag_device 4 0x1 0xf 0xe daemon_startup attach target arm920t little reset_run 0 arm920t working_area 0 0x200000 0x4000 backup run_and_halt_time 0 5000
For later versions of OpenOCD you may need to specify the device description. For the v2 Debug board add this line to your openocd.cfg:
ft2232_device_desc "Debug Board for Neo1973 A"
If you are using the libftdi version on Linux, and if you see this iProduct string in your lsusb output "Debug Board for Neo1973", please add this line instead.
ft2232_device_desc "Debug Board for Neo1973"
The telnet interface can be accessed using
telnet localhost 4444
it provides a plethora of functions for debugging. You might be interested in
reset reset halt resume poll reg load_binary mdw mww
First, you will need a suitable cross-gdb (a gdb that runs on your host architecture, e.g. i386, but works with code for arm). In OpenEmbedded, you can build such a cross-gdb by using
bitbake gdb-cross
If you want to debug the kernel, you can then start this gdb with
$ arm-linux-gdb vmlinux
which will give you something like
GNU gdb 6.6 Copyright (C) 2006 Free Software Foundation, Inc. GDB is free software, covered by the GNU General Public License, and you are welcome to change it and/or distribute copies of it under certain conditions. Type "show copying" to see the conditions. There is absolutely no warranty for GDB. Type "show warranty" for details. This GDB was configured as "--host=i686-linux --target=arm-linux"... (gdb)
We now need to connect to the OpenOCD daemon, which is done using the target remote command. In this particular example, we did already halt the target by issuing halt on the telnet command line
(gdb) target remote localhost:3333 Remote debugging using localhost:3333 warning: shared library handler failed to enable breakpoint 0xc0129b8c in memmove () at include/asm/current.h:9 9 { (gdb)
For breakpoints to work, you have to enable software breakpoints in OpenOCD, by issuing
> arm7_9 sw_bkpts enable
on the telnet command line, and use hbreak to set breakpoints in gdb.
Languages: |
English • العربية • Български • Česky • Dansk • Deutsch • Esperanto • Eesti • Español • فارسی • Suomi • Français • עברית • Magyar • Italiano • 한국어 • Nederlands • Norsk (bokmål) • Polski • Português • Română • Русский • Svenska • Slovenčina • Українська • 中文(中国大陆) • 中文(台灣) • Euskara • Català |