View source for Neo1973 Hardware/es
From Openmoko
You do not have permission to edit this page, for the following reasons:
You can view and copy the source of this page:
Template used on this page:
Return to Neo1973 Hardware/es.
You do not have permission to edit this page, for the following reasons:
You can view and copy the source of this page:
Template used on this page:
Return to Neo1973 Hardware/es.
OpenMoko Es un conjuto de aplicaciones (programas) que se encuentran en un nivel superior sobre una determinada plataforma (sin importar cual sea).El sistema físico (Hardware)del Neo1973 es la primera plataforma que toma la ventaja de usar la distribución OpenMoko . Puede encontar las epecificaciones del Neo1973 leyendos estas páginas de introducción y las páginas especifícas para el Neo1973 descritas en la parte de abajo.
El «cerebro» del sistema (CPU) Neo1973 es un Samsung S3C2410AL-26 (Con una frecuencia máxima de 266 MHz)
64MB Samsung NAND flash (K9F1208U0B) unida al controlador NAND S3C2410.
Ésta es la única memoria flash del dispositivo. El procesador S3C2410 se inicia directamente desde la nand usando el S3C2410 Steppingstone.
Sólo usamos programas libres (free software) y sistemas de archivos no propietarios para la flash. Para una descripción más detallada sobre cómo se ha usado, por favor diríjase a:NAND bad blocks
128MB SDRAM (2x Samsung K4M511633C) unida al controlador SDRAM S3C2410.
El sistema de comunicación (módem) GSM/GPRS está basado en el sistema Calypso de Texas Instruments.
Lamentamos no poder suministrar muchos detalles del Chipset GSM debido a exigencias estrictas establecidas en los Acuerdos de Confidencialidad (Non Disclosure Agreement, NDA). No obstante, el acceso a este nivel de información puede ser innecesario, puesto que este circuito integrado se conecta con el S3C2410 por medio de una conexión serie serie -UART- estándar. Esta interfaz está basada en siguientes normas: GSM 07.05, GSM 07.10
Página del producto: TWL3014
Página del producto: TRF6151
Soporta cuatro bandas RF
Soporta GPRS Clases 12/CS4
Hammerhead PMB 2520 AGPS de Global Locate.
No habrá un driver funcional hasta al menos mitad de Abril.
El Neo1973 dispone de una microSD, también conocida como ranura Transflash. Deberia también soportar SDHC, pero esta funcion no ha sido verificada. Si funciona, las tarjetas >2G deberian funcionar sin problemas. Como no existen tarjetas microSD sobre 2G por el momento, no ha sido posible realizar las verificaciones.
MicroSD slot is under battery.
Tiene un tamaño de 2,8 púlgadas -diagonal- (1,7" x 2,27" - 43mm x 58mm) con un tamaño de 480x640 pixeles. Usa el los módulos TD028TTEC1 y el Toshiba JBT6K74 TFT como controlador de la pantalla (LCD).
Aparentemente es similar a: ebay
Delta DFBM-CS320 Class2 Module, CSR BlueCore4
El controlador USB está incluído en S3C2410
The USB Device controller is inside the S3C2410
Puede ver: Neo1973 Audio Subsystem
There's a WM8753 Wolfson Microelectronics CODEC (This is not a 'smart' codec that can interpret MP3/... it is a simple dumb 'sound card'.
There's a National Semiconductor LM4857 Stereo Amplifier at the analog audio output of the WM8753
There's a four-ring 2.5mm stereo jack which provides connectivity to old-fashioned wired headsets.
The headsets used by Motorola smartphones (A780,A1200, ...) and the V-360 have a compatible configuration.
This one is wired via PCM bus from the CSR Bluetooth chip to the Wolfson codec.
El integrado PCF50606 de Philips es usado para tal fin.
La celda de energía Neo1973 es compatible con la betría BL5C de Nokia. De acuerdo a verLista . Foto de la pila, dentro del Neo1973.
El Neo1973 posee dos botones:
El primer prototipo, el más simple y sin «bluetooth».
First generation of prototypes that was given to internal OpenMoko software developers.
Unfortunately not useful at all due to non-working touchscreen.
Second generation of prototypes that was given to Harald + Mickey.
Unfortunately still not useful due to half-working touchscreen.
This is the bluetooth-enabled fork of GTA01
This is the first produced version of the bluetooth-enabled version.
This is the second produced version of the bluetooth-enabled version. It contains mainly GPS-related fixes.
This is the version that is shipped in Phase 0
Due to use of wrong GPIO/EINT pin, the PMU cannot wake-up the phone after suspend. This means, specifically, the following events can not bring the phone back from suspend-to-ram:
This is due to a design bug resulting in at least 30mA additional standby current, since we cannot properly switch off the power supply to the S3C2410 PLL's. There is nothing we can do to change this with post-production fixes. GTA01Bv4 will address this issue.
The GSM modem currently doesn't signalize a wakeup interrupt to the S3C2410 in case there's some noteworthy event, such as incoming call, loss of network, incoming SMS or the like.
This is a serious issue, but can be fixed with a GSM Modem Firmware update.
The local feedback sidetone (see [2]) is too loud. This will be addressed in a GSM firmware update
Due to an error in the production process, the factory-programmed NAND bad block information has been lost. This means that some blocks in the flash will wear out rapidly, which might become as bad as rendering the device unusable.
This is the version that will be shipped in Phase 1
Esta es las vista del impreso GTA01Bv4.
Every hardware revision has its own u-boot image type. Thus, the bootloader has the revision hard-coded. The hardware revision is passed on to the kernel via the ATAG mechanism (ATAG_REVISION)
The kernel receives the ATAG_REVISION during bootup, and saves its contents in the "system_rev" global variable.
The kernel exports the system_rev variable in /proc/cpuinfo as "Revision :" line.
Languages: |
English • العربية • Български • Česky • Dansk • Deutsch • Esperanto • Eesti • Español • فارسی • Suomi • Français • עברית • Magyar • Italiano • 한국어 • Nederlands • Norsk (bokmål) • Polski • Português • Română • Русский • Svenska • Slovenčina • Українська • 中文(中国大陆) • 中文(台灣) • Euskara • Català |