View source for Neo FreeRunner Wifi
From Openmoko
You do not have permission to edit this page, for the following reasons:
You can view and copy the source of this page:
Template used on this page:
Return to Neo FreeRunner Wifi.
You do not have permission to edit this page, for the following reasons:
You can view and copy the source of this page:
Template used on this page:
Return to Neo FreeRunner Wifi.
root@om-gta02:~# iwlist eth0 scan
Once you have a /etc/wpa_supplicant/wpa_supplicant.conf file, add a line under the eth0 entry in /etc/network/interfaces:
iface eth0 inet dhcp wpa-conf /etc/wpa_supplicant/wpa_supplicant.conf
Save your changes and run:
# ifdown eth0 && ifup eth0
You'll get a lot of messages, like ioctl[SIOCSIWENCODEEXT]: Operation not supported and sed: unrecognized option `--quiet', they appear to be harmless. The "--quiet" error message can be avoided by replacing "sed --quiet" with "sed -n" in /etc/wpa_supplicant/*.sh
iface eth0 inet dhcp
wireless-key my_wep_key wireless-essid my_essid
iface eth0 inet dhcp wpa-wep-key0 my_wep_key wpa-key-mgmt NONE wpa-ssid my_essid
Save your changes and run:
# ifdown usb0 && ifup eth0
Create and edit a suitable /etc/wpa_supplicant/wpa_supplicant.conf
root@om-gta02:~# ifup eth0 root@om-gta02:~# wpa_supplicant -ieth0 -c/etc/wpa_supplicant/wpa_supplicant.conf -B root@om-gta02:~# udhcpc eth0
ctrl_interface=/var/run/wpa_supplicant ctrl_interface_group=0 eapol_version=1 ap_scan=1 fast_reauth=1 # WPA2: network={ ssid="your ssid" scan_ssid=1 proto=RSN key_mgmt=WPA-PSK pairwise=CCMP TKIP group=TKIP CCMP psk="secret key" priority=50 } # WPA: network={ ssid="your_ssid" proto=WPA key_mgmt=WPA-PSK pairwise=TKIP group=TKIP scan_ssid=1 psk="secret key" priority=10 } # WEP: network={ ssid="your_ssid" scan_ssid=1 key_mgmt=NONE wep_tx_keyidx=0 wep_key0=your_hex_key priority=8 } # Open: network={ ssid="your ssid" key_mgmt=NONE priority=5 }
#!/bin/sh # # wlan This shell script starts and stops wlan. # # processname: wlan # Source function library. #. /etc/rc.d/init.d/functions # "written" by HdR RETVAL=0 prog="wlan" # test -f /etc/default/$prog && . /etc/default/$prog start() { echo -n "Starting $prog: " ifconfig eth0 up wpa_supplicant -ieth0 -c/etc/wpa_supplicant/wpa_supplicant.conf -B sleep 10 udhcpc eth0 RETVAL=$? return $RETVAL } stop() { # Stop daemons. echo -n "Shutting down $prog: " killall wpa_supplicant ifconfig eth0 down # killproc gpsd RETVAL=$? return $RETVAL } # See how we were called. case "$1" in start) start ;; stop) stop ;; restart|reload) stop start RETVAL=$? ;; *) echo "Usage: $0 {start|stop|restart}" exit 1 esac exit $RETVAL
wpa_supplicant 0.6.3-r1 works for me with WPA and WPA2 (with PSK) using the config file template on this page. Unlike the comment above, udhcpc is updating /etc/resolver.conf correctly for me (perhaps this is an old problem).
Bringing up wpa_supplicant manually or using "ifup eth0" with the wpa-conf option set in /etc/network/interfaces works for me. If usb0 was already up when running "ifup eth0" you'll end up with 2 default routes which can cause problems. To solve this either take usb0 down first or run "ip route del default dev usb0" to remove the default route to usb0.
I've had repeated success with:
# ifconfig eth0 up # iwconfig eth0 essid any # iwconfig eth0 key '...' # iwconfig eth0 essid '...' # udhcpc eth0 # ifconfig usb0 down; ifconfig usb0 up
Hope that helps someone. This is for WEP.
I've been able to connect to a variety of networks including WPA2 without too much difficulty. Follow the above steps in configuring your wpa_supplicant.conf and adding the line to load the supplicant in /etc/network/interfaces.
My sample WPA2 configuration is as follows:
network={
ssid="MY_SSID" scan_ssid=1 proto=RSN key_mgmt=WPA-PSK pairwise=CCMP TKIP group=CCMP TKIP psk="PASSWORD_PRESHARED_KEY" priority=50
}
That configuration will allow you to connect to a WPA2-Personal network with TKIP key encryption.
The "ifup eth0" command will connect you via WiFi. If you don't get a lease the first time, try again. Sometimes the configuration is a little too slow and DHCP tries to get a lease before a successful connection to your access point has been established.
The following may be helpful in order to scan available networks :
# iwlist eth0 scan
lint-wifi work in progress
http://wiki.openmoko.org/wiki/Lint-wifi